Views: 605 Author: Site Editor Publish Time: 2021-03-04 Origin: Site
Shenzhen Chengzhiyi Circuit Co., Ltd. was established in 20082007. It is a national high-tech enterprise specializing in the R&D, manufacturing and sales services of PCB circuit boards and 200PCBA , with nearly 100 employees.
Since its establishment, after 12more than years of industry experience and accumulation, Chengzhiyi has established a unique product R&D, production and quality management service system, creating a highly capable production, R&D and sales service team. The main products include various MCPCB aluminum substrates / copper substrates; PCB double-sided multilayer boards, Rigid-Flex PCB soft and hard combination boards , PCBA module boards and patch assembly, etc. Products are widely used in new energy vehicles, industrial control and automation, LED lighting, 5G communication equipment, industrial electronic control, high-power electricity, medical equipment, intelligent security and other industries. Up to now, the comprehensive monthly output of Chengzhiyi circuit boards has reached 30000square meters.
1. The characteristic of the wiring design of the new energy vehicle battery circuit board is that it should be as short as possible. This should be changed even more in high-frequency circuits. The turns of the new energy vehicle battery circuit board wires should be rounded, while right angles or sharp corners will affect the electrical performance in high-frequency circuits and high wiring density; when two panels When wiring, the wires on both sides should be routed perpendicularly, obliquely, or bent to each other, and avoid being parallel to each other to reduce parasitic coupling; the new energy vehicle battery circuit board wires used as circuit input and output should avoid adjacent parallel lines as much as possible to avoid feedback. It is best to add a ground wire between these wires.
2. The width of the new energy vehicle battery circuit board wires should meet the electrical performance requirements and facilitate production. Its minimum value is determined by the current it can withstand, but the minimum should not be less than 0.2mm. In high-density, high-precision lines, the wire width and spacing are generally 0.3mm; the wire width is generally 0.3mm in large electrical circuits. The temperature rise must also be considered under current conditions. The single-sided line inverse PCB experiment shows that when the copper foil thickness is 50μm, the wire width is 1~1.5mm, and the passing current is 2A, the temperature rise is very small. Therefore, generally using 1~1.5mm width wires may meet the design requirements without causing temperature rise; new energy vehicle battery lines The common ground wire of the circuit board wires should be as thick as possible. If possible, use lines larger than 2 to 3 mm. This is especially important in circuits with microprocessors, because when the ground wire is too thin, due to changes in the flowing current, ground potential changes, and the level of the microprocessor timing signal is unstable, which will degrade the noise margin; in DI The 10-10 and 12-12 principles can be applied to the wiring between the IC pins of the P package. That is, when two wires pass between the two pins, the pad diameter can be set to 50mil, and the line width and line spacing are both 10mil. When only one wire passes between the two pins, the pad diameter can be set to 64mil, and the line width and line spacing are both 12mil.
3. Spacing between new energy vehicle battery circuit board wires: The spacing between adjacent wires must meet electrical safety requirements, and in order to facilitate operation and production, the spacing should be as wide as possible. The minimum spacing must be at least adequate for the voltage to be tolerated. This voltage generally includes operating voltage, additional fluctuation voltage and peak voltage caused by other reasons. If the relevant technical conditions allow a certain degree of metal particles between the conductors, the spacing will be reduced. Therefore, voltage must be considered when designing. When the wiring density is low, the spacing between signal lines can be appropriately increased. Signal lines with a huge difference between high and low levels should be as short as possible and the spacing should be increased.
4. Shielding and grounding of the printed wires of the new energy vehicle battery circuit board: The common ground wire of the printed wires of the new energy vehicle battery circuit board should be arranged on the edge of the printed circuit board as much as possible. As much copper foil as possible should be retained on the printed circuit board as a ground wire. The shielding effect obtained in this way is better than a long ground wire. The transmission line characteristics and shielding effect will be improved, and it also plays a role in reducing distributed capacitance. The common ground wire of the printed conductor of the new energy vehicle battery pack circuit board is best to form a loop or mesh. This is because when there are many integrated circuits on the same board, especially when there are components that consume a lot of power, a ground potential difference is generated due to graphic limitations, which causes a reduction in the noise margin. When a loop is made, the ground potential difference is reduced. In addition, the grounding and power supply patterns should be as parallel as possible to the direction of data flow, which is the secret to enhanced noise suppression capabilities; several layers of multi-layer printed circuit boards can be used as shielding layers, and the power layer and ground layer can be regarded as shielding layers. Generally, the ground layer and power layer are designed on the inner layer of the multi-layer printed circuit board, and the signal lines are designed on the inner and outer layers.